My existing PRESTIGE APS95BT2 ELVAT5C remote is broken. I can buy one on-line for $25 but how do i reprogram it - Prestige Electronics Prestige Aps95bt2 Elvat5c question. My existing PRESTIGE APS95BT2 ELVAT5C remote is broken. I can buy one on-line for $25 but how do i reprogram it - Prestige Electronics Prestige Aps95bt2 Elvat5c question. Specifications Condition Pre-Owned 556o FCC ID ELVAT5C Interchangeable FCC IDs BGAAPS2T ELVAT5C Part# BAOE2BT Interchangeable Part #s: BAOE2BT APS95BT2 BA0E2BT Interchangeable circuit board # AT0K AT4B Dealer part # Buttons 2: buttons; LED Red Frequency 302 - 309 MHz Battery Type 1: GP23A Additional Information Condition Explanation: Pre-Owned Pre-Owned: An item that has been used previously. The item may have some signs of cosmetic wear, but is fully operational and functions as intended. Scroll through listing for full details and description of any imperfections. _____________________________ PROGRAMMING: Programming Instructions: It is important to remember that during programming, each individual step of the procedure must be executed within 15 seconds of the previous step. When the 15 second time limit is allowed to expire, the system will automatically exit program mode. This is indicated by a long 'chirp' from the siren. Additionally, any time the ignition key is turned off while programming, the system will immediately exit program mode. This is also indicated by a long 'chirp' from the siren. To program additional transmitters: 1. Enter the vehicle, and turn the ignition key to the 'on' position. Flip the valet switch on - off - on - off - on - then off. 3.The dash LED will flash once, and the siren will 'chirp' once, indicating the system is ready to accept programming for channel 1 or the arm/ disarm and panic functions. You can assign any of the three transmitter button functions listed below to channel 1 a. Pressing button #1 on the keychain transmitter. Pressing button #2 on the keychain transmitter. Pressing both buttons simultaneously on the keychain transmitter. Press and hold the selected choice a, b, or c above, until the siren emits a long 'chirp' to confirm that programming of channel 1 was successful. Move the valet/bypass switch on, then off again. The dash mounted LED will flash 2 times, and the siren will 'chirp' indicating that the system is ready to accept programming for channel 2, or the pulsed ground output for remote trunk release, remote car starter, etc. You can assign any one of the two remaining button functions listed in 4a, 4b, or 4c above to operate channel 2. You cannot use the button(s) that operate channel 1, selected in step 5, to operate channel 2. Press and hold the selected choice. The siren will emit a long 'chirp' to confirm that programming of channel 2 was successful. Move the valet/bypass switch on, then off again. 11.The dash mounted LED will flash 3 times, and the siren will 'chirp' indicating that the system is ready to accept programming for channel 3. (APS 350) 12. Press and hold the remaining transmitter button function. The siren will emit a long 'chirp' to confirm that programming of channel 3 was successful. To exit program mode, either turn the ignition key to the off position, or move the valet switch on then off one additional time. This is indicated by one short chirp then one long 'chirp' from the siren. NOTE: If programming to a Keyless Entry (non alarm) unit, there will be NO chirp indication. QUICK REFERENCE You can program any individual channel, without reprogramming all channels, by following the quick reference chart below. Channel - Valet Switch - LED 1 - On then off 3 times - 1 flash 2 - On then off 4 times - 2 flashes 3 - On then off 5 times - 3 flashes After the desired channel is programmed, turn the ignition key to the off position to exit programming mode. • All remotes include working batteries (except case-only purchases) • A purchased remote needs to be programmed after you receive it in order to work with your specific vehicle. There are two possiblities that could prove to be the fault; hood pin switch and remote start shutdown switch. If the vehicle is equipped with a hood shut down switch, you will need to make an adjustment to it for the remote starter to function. Search around the drivers side edges of the engine compartment for a push pin.If the pin is a stand alone it will be mounted near the headlight inserted into an existing hole. It may also be attached to a bracket. The remote start shutdown switch is a toggle switch located under the drivers side of the dash,usually to the left of the brake pedal, depending on the installation. If nothing above solves the problem, you may need to reprogram the remote to the unit. May 23, 2011|. The programming procedure for Prestige/Pursuit remote is as follows: First, locate the programming/valet switch. For newer model units the programming switch is located in the antenna, previous models have a push button LED (PBLED). Older models have a plain black push button, usually located near the driver's side kick panel (where your left foot would rest when driving). After locating the programming switch; turn ignition on, press and release switch three (3) times,parking lights will flash once.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |